Seamless Rain Gutters

Seamless Rain Gutters in Grafton County, New Hampshire (NH)

From one end of Grafton County to the other, our crews form gutters on site so each run goes up whole, with the coil color settled against your trim first.

Measure my home for free

A written figure after a real measure, and the decision stays yours.

Why one piece beats twenty-two

A sectional gutter arrives from a shelf in short lengths and gets stitched together on your fascia. A seamless gutter leaves our machine as a single ribbon of aluminum, already the length of the run it will serve. Everything below follows from that difference.

What mattersSeamless, formed on siteSectional, stitched from parts
Joints along a 40 ft runNone between the end capsRoughly a dozen snap or rivet joints
Where leaks startCorners and outlets, the only sealed spotsEvery joint is a future drip line
Freeze and thawOne piece moves as one pieceIce pries each joint a little wider every winter
The look from the curbA single straight line of metalVisible seams and slight steps at each section
UpkeepRinse it, check the corners once a yearChase and reseal joints as they let go
Working lifeDecades when hung on solid fasciaShorter, and it retires one leak at a time

Profiles and sizes we roll

The machine changes its forming head, not its habits. Whichever profile your house calls for, the run still comes off the coil in one piece.

ProfileWhat it carriesHomes it suitsDownspouts that pair
5 inch K-styleThe everyday choice for most single family roofsStandard rooflines with moderate pitch and area2x3 inch rectangular
6 inch K-styleNoticeably more capacity for the same clean profileSteep or large roofs, metal roofing, heavy rain country3x4 inch rectangular
Half roundA smooth open trough that sheds debris wellHistoric homes, copper lovers, low-debris rooflines3 or 4 inch round

Not sure which size your roof sheds into? That is a measuring question, not a guessing question, and the measure is free.

The craft, run by run

  • The measure that rules the job

    The measure that rules the job

    Every fascia gets walked and taped before anything is ordered. The numbers written that day are the numbers the machine obeys.

  • Forming at the curb

    Forming at the curb

    Flat coil goes into the roll former on the truck and a finished gutter profile comes out, cut off at the length of your run and not an inch more.

  • Hanging to a true pitch

    Hanging to a true pitch

    Hidden hangers screwed into sound fascia, spaced for snow country where it applies, with a fall toward the outlet you can check with a hose.

  • Corners mitered by hand

    Corners mitered by hand

    The only seams a seamless system has live at the corners, so ours are cut, lapped, riveted and sealed like they matter. Because they do.

  • Downspouts that finish the story

    Downspouts that finish the story

    Sized to the gutter that feeds them, dropped where the water should land, with extensions that carry it clear of the foundation.

  • Color read against your trim

    Color read against your trim

    Factory painted coil comes in dozens of stock shades. We hold the chart against your fascia in daylight, not in a catalog.

The machine comes to you

  1. Send the form

    ZIP, the kind of run, your name and number. Under a minute, and nothing else is asked of you yet.

  2. The callback

    A measurer rings back inside a working day, hears the roofline out and books a time that suits the house.

  3. Tape on fascia

    Runs, drops, corners and colors are measured and settled on site. You get one written figure that holds.

  4. The machine arrives

    Forming day. The truck parks, the coil rolls, and each gutter comes off at the exact length it was measured for.

  5. Hung and rinsed

    Runs go up on hidden hangers, corners are sealed, downspouts dropped, and water is run through before we pull away.

What a foot of gutter costs

Line on the quoteTypical bracketRead this first
5 inch K-style aluminum, formed and hung$9 - $14 per ftThe bracket most single story homes land in.
6 inch K-style aluminum, formed and hung$11 - $17 per ftBigger coil, beefier hangers, same one-piece runs.
Half round, aluminum$16 - $28 per ftCopper is quoted per project, coil prices move too much to print.
Taking down and hauling old gutters$1 - $2 per ftIncludes the fasteners, the sealant crumbs and the trip to recycling.
Downspouts, each$80 - $180Depends on stories, elbows and where the water has to land.
Small job minimumStated on the quoteThe machine travels whole; short runs share the trip cost honestly.

Stories, ladder access and fascia condition move a footage price up or down, which is why we measure before we promise. The figure you sign is the figure you pay.

Color comes off the coil, not out of a paint can

Seamless gutter stock arrives as factory painted aluminum coil, baked finish on both faces, in dozens of standing shades from bright white through bronzes and into true black. Because the color is cured onto the metal before it ever reaches the forming machine, it does not brush off, and it weathers evenly along the whole run.

Matching is done at your house. The measurer brings the coil chart to the fascia and reads it in your daylight, against your trim, your siding and your roof edge. Most homes want the gutter to disappear into the trim line; some want the downspouts to vanish against the siding instead, and the two choices are allowed to differ. If your trim sits between two stock shades, we will say so plainly and show you both instead of promising a custom tint we cannot roll.

What homeowners ask before signing

What does seamless actually mean here?

Each straight run is one continuous piece of metal, formed at your house to the length of that fascia. The only joints in the whole system sit at corners and outlets, where they are riveted and sealed by hand.

How long does the machine spend at my house?

For most homes the forming and the hanging fit inside a single visit. Long wraparound rooflines or three stories of ladder work can stretch it, and the quote says so before anyone commits.

Can you really match my trim color?

From dozens of factory painted coil shades, almost always closely enough that visitors never think about it. When your trim falls between two stock shades, you see both charts at the fascia and pick with your own eyes.

What happens to the gutters already on the house?

They come down the same day, fasteners and all, and leave in our truck for recycling. The tear off is its own line on the written quote, never a surprise.

Are corners a weak point?

They are the only seams the system has, which is exactly why they get the slow treatment: hand cut miters, riveted laps and sealant rated for wet metal. A corner done that way outlives the sealant tube it came from many times over.

Is a small house worth a seamless run?

Yes, the machine rolls a 20 ft run as happily as a 60 ft one. A small job minimum applies because the truck travels whole, and it is printed on the quote so you can judge it in writing.

1 pieceper straight run, end cap to end cap
Fifty statesand the machine rolls in every one
To the inchevery run cut off the coil at its measured length
$0for the measure and the written figure

Rooflines around Grafton County

The terrain sets the pitch and the trees set the debris. The lists further down name every community the truck reaches from here.

Towns of Grafton County on our route sheet

The rest of New Hampshire, county after county

One ribbon of metal per run, and the drips have nowhere left to start.

Get my written figure